IEC-60204-11-2000 pdf free download – Safety of machinery – Electrical equipment of machines – Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV.
IEC 60204 applies to the electrical and electronic equipment and systems of machines,including a group of machines working together in a coordinated manner, but excluding higherlevel system aspects (i.e.communications between systems).
This part of lEC 60204 is applicable to equipment,or parts of equipment,which operate withnominal supply voltages above 1 000 V a.c.or 1 500 v d.c. and not exceeding 36 kV a.c. ord.c. with nominal frequencies not exceeding 200 Hz. For higher voltages or frequencies,special requirements may be needed.
ln this standard， the term HV equipment also covers the LV equipment forming an integralpart of the equipment operating at high voltage.The requirements in this standard primarilycover the parts operating at high voltage except where explicitly stated otherwise.Referenceis made to lEC 60204-1 for those requirements which also apply to HV equipment.
NOTE1 Other LV equipment not forming part of the HV equipment and defined as operating at voltages notexceeding 1 0o0 v a.c. or 1 500 v d.c.are covered by lEC 60204-1.
NOTE 2 In this standard,the term “electrical”includes both electrical and electronic matters (.e. electricalequipment means both the electrical and the electronic equipment).
The electrical equipment covered by this part of lEC 60204 commences at the point ofconnection of the supply to the electrical equipment of the machine (see 5.1).
NOTE 3 For the requirements for power supply installations, see HD 637.
This part of lEC 60204 is an application standard and is not intended to limit or inhibittechnological advancement. lt does not cover all the requirements (e.g. guarding,interlockingor control) which are needed or required by other standards or regulations in order tosafeguard personnel from hazards other than electrical hazards.Each type of machine hasunique requirements to be accommodated to provide adequate safety.
NOTE 4 In the context of this standard, the term “person” refers to any individual; “personnel” are those personswho are assigned and instructed by the user or his agent(s) in the use and care of the machine in question.
This part of lEC 60204 specifically includes, but is not limited to, machines as defined in 3.26(annex A lists examples of machines whose electrical equipment may be covered by thisstandard).
Additional and special requirements can apply to the electrical equipment of machines that
– are used in the open air (i.e. outside buildings or other protective structures);
– use, process or produce potentially explosive material (e.g. paint or sawdust);
– are used in potentially explosive and/or flammable atmospheres;
– have special risks when producing or using certain materials;
– are used in mines.
Power circuits where electrical energy is directly used as a working tool are excluded from this part of IEC 60204.
2Normative references
The following normative documents contain provisions which，through reference in this text,constitute provisions of this part of lEC 60204.For dated references,subsequent amend-ments to，or revisions of，any of these publications do not apply. However，parties toagreements based on this part of lEC 60204 are encouraged to investigate the possibility ofapplying the most recent editions of the normative documents indicated below. For undatedreferences, the latest edition of the normative document referred to applies. Members of lSoand lEC maintain registers of currently valid lnternational Standards.
IEC 60034-1:1996,Rotating electrical machines – Part 1 : Rating and performance
IEC 60050(191):1990，International Electrotechnical Vocabulary (IEV) – Chapter 191:Dependability and quality of service
IEC 60050-195:1998,International Electrotechnical Vocabulary (IEV) – Part 195: Earthingand protection against electric shock
IEC 60050(441):1984,International Electrotechnical Vocabulary (IEV) – Chapter 441 :Switch-gear, controlgear and fuses
IEC 60050(826):1982，International Electrotechnical Vocabulary (IEV) – Chapter 826:Electrical installations of buildings
IEC 60050(826):1995, amendment No.2
IEC 60071-1:1993,Insulation co-ordination – Part 1 : Definitions, principles and rulesIEC 60071-2:1996,Insulation co-ordination – Part 2: Application guide
IEC 60076-5:1976,Power transformers – Part 5: Ability to withstand short-circuitIEC 60129:1984,Alternating current disconnectors and earthing switches
IEC 60204-1:1997，Safety of machinery – Electrical equipment of machines – Part 1: Generalrequirements
IEC 60298:1990，A.C. metal-enclosed switchgear and controlgear for rated voltages above1 kV and up to and including 52 kV
IEC 60364-4-41:1992，Electrical installations of buildings – Part 4: Protection for safety -Chapter 41: Protection against electric shock.IEC-60204-11 pdf download.