BS IEC 62003-2020 pdf free download – Nuclear power plants — Instrumention, control and electrical power systems — Requirements for electromagnetic compatibility testing.
This documentestablishes requirements for electromagnetic compatibility testing ofinstrumentation，control,and electrical equipment supplied for use in systems important tosafety at nuclear power plants and other nuclear facilities. The document lists the applicableIEC standards (principally the IEC 61000 series) which define the general test methods,andprovides the necessary application-specific parameters and criteria to ensure that nuclearsafety requirements are met.
The normative part of this document is limited to the testing of equipment prior to installationin a nuclear power plant to demonstrate immunity to electromagnetic disturbances and todemonstrate that the equipment does not generate excessive emissions. Testing for thegeneration of excessive emissions is also applicable to non-safety equipment.This documentincludes informative annexes which provide additional guidance and describes approaches tomaintaining electromagnetic compatibility for installed equipment. The intent of this documentis to provide guidance for conducting the electromagnetic compatibility (EMC) qualificationtesting of the equipment and does not provide guidance for the installation of the equipmentto prevent electromagnetic and radio frequency interference (EMI/RFI). However，theconfiguration of the equipment under test during EMC qualification testing is representative ofthe intended installation in a nuclear facility.
Protection against a high altitudeelectromagnetic pulse (HEMP) and intentionalelectromagnetic interference (IEMI) are outside of the scope of this document, but informationcan be found in IEC 61000-4-23，IEC 61000-4-24, and IEC 61000-4-25 (HEMP) andlEC 61000-4-36(IEMl) to address these phenomena.
2Normative references
The following documents are referred to in the text in such a way that some or all of theircontent constitutes requirements of this document.For dated references，only the editioncited applies.For undated references, the latest edition of the referenced document (includingany amendments) applies.
IEC/IEEE 60780-323，Nuclear facilities – Electrical equipment important to safety -Qualification
IEC TR 61000-1-6，Electromagnetic compatibility (EMC) – Part 1-6:General – Guide to theassessment of measurement uncertainty
IEC TR 61000-2-5,Electromagnetic compatibility(EMC) – Part 2-5: Environment -Description and classification of electromagnetic environments
IEC 61000-4-2，Electromagnetic compatibility (EMC) – Part 4-2: Testing and measurementtechniques – Electrostatic discharge immunity test
IEC 61000-4-3，Electromagnetic compatibility (EMC) – Part 4-3: Testing and measurementtechniques – Radiated, radio-frequency, electromagnetic field immunity test
IEC 61000-4-4，Electromagnetic compatibility (EMC) – Part 4-4: Testing and measurementtechniques – Electrical fast transient/burst immunity test
IEC 61000-4-5，Electromagnetic compatibility(EMC) – Part 4-5: Testing and measurementtechniques – surge immunity test
IEC 61000-4-6，Electromagnetic compatibility(EMC) – Part 4-6: Testing and measurementtechniques – lmmunity to conducted disturbances, induced by radio-frequency fields
IEC 61000-4-8，Electromagnetic compatibility(EMC) – Part 4-8: Testing and measurementtechniques – Power frequency magnetic field immunity test
IEC 61000-4-9，Electromagnetic compatibility (EMC) – Part 4-9: Testing and measurementtechniques – Impulse magnetic field immunity test
IEC 61000-4-10，Electromagnetic compatibility (EMC) – Part 4-10:Testing and measurementtechniques -Damped oscillatory magnetic fieid immunity test
IEC 61000-4-11，Electromagnetic compatibility (EMC) – Part 4-11: Testing and measurementtechniques – Voltage dips,short interruptions and voltage variations immunity tests
IEC 61000-4-12，Electromagnetic compatibility (EMC) – Part 4-12:Testing and measurementtechniques – Ring wave immunity test
IEC 61000-4-13，Electromagnetic compatibility (EMC) – Part 4-13:Testing and measurementstechniques – Harmonics and interharmonics including mains signalling at a.c. power port, lowfrequency immunity tests
IEC 61000-4-14，Electromagnetic compatibility (EMC) – Part 4-14:Testing and measurementtechniques – voltage fluctuation immunity test
IEC 61000-4-16，Electromagnetic compatibility (EMC) – Part 4-16: Testing and measurementtechniques – Test for immunity to conducted，common mode disturbances in the frequencyrange o Hz to 150 kHz
IEC 61000-4-17，Electromagnetic compatibility (EMC) – Part 4-17: Testing and measurementtechniques – Ripple on d.c.input power port immunity test
IEC 61000-4-18，Electromagnetic compatibility (EMC) – Part 4-18:Testing and measurementtechniques – Damped oscillatory wave immunity test
IEC 61000-4-20，Electromagnetic compatibility (EMC) – Part 4-20:Testing and measurementtechniques – Emission and immunity testing in transverse electromagnetic(TEM) waveguides
IEC 61000-4-28，Electromagnetic compatibility (EMC) – Part 4-28:Testing and measurementtechniques – Variation of power frequency, immunity test
IEC 61000-4-29，Electromagnetic compatibility(EMC) – Part 4-29:Testing and measurementtechniques – Voltage dips,short interruptions and voltage variations on d.c. input power portimmunity tests.BS IEC 62003 pdf download.