IEC 62067-2011 pdf free download – Power cables with extruded insulation and their accessories for rated voltages above 150 kV (U m = 170 kV) up to 500 kV (U m = 550 kV) – Test methods and requirements.
This International Standard specifies test methods and requirements for power cable systems,cables with extruded insulation and their accessories for fixed installations, for rated voltagesabove 150 kV(Um = 170 kV) up to and including 500 kV (um = 550 kV).
The requirements apply to single-core cables and to their accessories for usual conditions ofinstallation and operation, but not to special cables and their accessories,such as submarinecables，for which modifications to the standard tests may be necessary or special testconditions may need to be devised.
This standard does not cover transition joints between cables with extruded insulation andpaper insulated cables.
2Normative references
The following documents, in whole or in part, are normatively referenced in this document andare indispensable for its application. For dated references,only the edition cited applies.Forundated references, the latest edition of the referenced document (including any amendments)applies.
NOTE The IEC 60811 series is currently undergoing a revision，which will lead to a restructuring of its parts. Adescription of this, as well as a cross-reference table between the current and planned parts will be given inIEC 60811-100.
IEC 60060-1 High-voltage test techniques – Part 1: General definitions and test requirements
IEC 60183，Guide to the selection of high-voltage cables
IEC 60228,Conductors of insulated cables
IEC 60229:2007，Electric cables – Tests on extruded oversheaths with a special protectivefunction
IEC 60230,lmpulse tests on cables and their accessories
IEC 60287-1-1:2006，Electric cables – Calculation of the current rating – Part 1-1:Currentrating equations (100 % load factor) and calculation of losses – General
IEC 60332-1-2，Tests on electric and optical fibre cables under fire conditions – Part 1-2:Testfor vertical flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixedflame
IEC 60811-1-1:1993,Common test methods for insulating and sheathing materials of electriccables and optical cables – Section 1-1: Methods for general application – Measurement ofthickness and overall dimensions – Tests for determining the mechanical properties
Amendment 1 (2001)
IEC 60811-1-2:1985,Common test methods for insulating and sheathing materials of electriccables – Part 1: Methods for general application – Section Two: Thermal ageing methods
Amendment 1 (1989)
Amendment 2 (20oo)
IEC 60811-1-3:1993,Common test methods for insulating and sheathing materials of electriccables – Part 1-3: General application – Methods for determining the density – Waterabsorption tests – Shrinkage test
Amendment 1 (2001)
IEC 60811-1-4:1985,Common test methods for insulating and sheathing materials of electriccables – Part 1: Methods for general application – Section Four: Tests at low temperatureAmendment 1 (1993)
Amendment 2 (2001)
IEC 60811-2-1:1998,Common test methods for insulating and sheathing materials of electricand optical cables – Part 2-1: Methods specific to elastomeric compounds – Ozone resistance,hot set and mineral oil immersion tests
Amendment 1 (2001)
IEC 60811-3-1:1985,Common test methods for insulating and sheathing materials of electriccables – Part 3: Methods specific to PVC compounds – Section 1: Pressure test at hightemperature – Tests for resistance to cracking
Amendment 1 (1994)
Amendment 2 (2oo1)
IEC 60811-3-2:1985,Common test methods for insulating and sheathing materials of electriccables – Part 3: Methods specific to PVC compounds – Section two: Loss of mass test -Thermal stability test
Amendment 1 (1993)Amendment 2 (20o3)
IEC 60811-4-1:2004,Insulating and sheathing materials of electric and optical cables -Common test methods – Part 4-1: Methods specific to polyethylene and polypropylenecompounds – Resistance to environmental stress cracking -Measurement of the melt flowindex – Carbon black and/or mineral filler content measurement in polyethylene by directcombustion – Measurement of carbon black content by thermogravimetric analysis (TGA) -Assessment of carbon black dispersion in polyethylene using a microscope
IEC 60885-3，Electrical test methods for electric cables – Part 3: Test methods for partialdischarge measurements on lengths of extruded power cables.IEC 62067 pdf download.